|
 |
 |
|
 |
|
Memtech 3.5" IDE, SATA, and Fibre Channel
Solid State Flash Drives |
|
|
|
AT3600
Wolverine - 3.5" IDE Solid State Flash Drive |
|
|
| This
product has reached End-of-Life status but limited quantities
are still available. Please contact the SSD Team at (949)
260-8345 for last time purchase and replacement product
information. |
| PDF
Data Sheet | User
Guide |
|
12 Gbyte capacity under 16mm (0.63")
60 Gbyte maximum capacity
Full -55°C to +125°C military temp. range
3.5" drive low profile form-factor
UDMA-66 compliant IDE interface
16 byte CRC/ECC and Active Remap(TM) for exceptional data reliability
Kicker(TM) Hold Up Circuit
Active Remap(TM) Data Reliability Feature |
5 volt, low power operation
Completely solid state - no moving parts
2000G operating shock
20G operating vibration
0.1 millisecond random access time
26 Mbyte/sec cached Read performance
20 Mbyte/sec cached Write performance
5 year product warranty
8 million erase/write cycle endurance |
|
The AT3600 solid-state flash drive is an UDMA-66 compliant IDE memory module offered in an extremely low profile 3.5 inch drive form-factor. The drive is completely solid state, with no moving parts. This contributes to the unit's exceptional ruggedness and wide operating temperature range; with no moving parts, there is no mechanism for mechanical wear-out. Being 100% IDE compatible, no special drivers or flash file managers are required to interface the drive. It is a virtual drop in replacement for standard rotating media.
The primary storage media in the drive is sector-erasable NAND E2PROMs (Flash). Using these devices, Memtech is able to deliver up to 60 Gbytes of uncompressed, non-volatile solid-state storage in an extremely small, rugged form-factor. The access time for the drive is under 0.1 millisecond, which permits thousands of transactions to occur per second. Cached read data performance is 26 Mbytes/second, and cached write performance is 20 Mbytes/second.
The Kicker(TM) Hold Up Circuit, using ultra-cap technology, meets all the requirements for a robust and reliable solution. Ultra-caps are new, high-energy capacitors that offer an extremely low ESR, wide operating temperature and small footprint. Unlike batteries, they offer a much more robust form of energy storage, with a wider operating temperature and longer life. Combined with some innovative firmware control, back-EMF and surge current suppression and power monitoring, the Kicker(TM) virtually eliminates the chance of corrupted data in the flash array due to a power loss.
The interface is implemented using a commercially available UDMA-66 compliant IDE controller with a large buffer and a 16-byte combination CRC/ECC error detection and on-the-fly correction mechanism that greatly improves data reliability. The CRC/ECC circuitry, in conjunction with Memtech's proprietary Active Remap(TM) technology, makes for a virtually bulletproof medium for data storage. The drive supports advanced PIO, DMA and UDMA transfer modes, multi-sector transfers, and LBA addressing.
The AT3600 is available now in standard capacities ranging from 2 to 60 Gbytes. The AT3600 low profile solution of 1 to 12 Gbytes capacities is available in a 16mm height and up to 20 Gbytes capacity within a 20mm height restriction.
Every drive is subjected to Memtech's EnduroTest(TM) in which it is fully tested under environmental and voltage extremes to guarantee data integrity under even the harshest conditions, and to ensure full functionality out of the box.
The AT3600 may be mounted in any orientation. Eight mounting holes are available: four on the bottom and four on the sides. All holes are tapped 6-32 with a maximum penetration of 0.25 inches. |
| Back to top |
|
AT3515 Bulldog - 3.5" IDE Solid State Flash Drive |
|
|
| This
product has reached End-of-Life status but limited quantities
are still available. Please contact the SSD Team at (949)
260-8345 for last time purchase and replacement product
information. |
| PDF
Data Sheet | User
Guide |
|
128Mbyte to 8Gbyte uncompressed capacity
Full -40°C to +85°C industrial temp. range
Low profile 3.5" drive form-factor
Standard 40 pin, unitized IDE interface
72-bit ECC for exceptional data reliability
5 volt, low power operation |
Completely solid state - no moving parts
1000G operating shock
15G operating vibration
6 Mbytes/sec Read throughput
6 Mbytes/sec Write throughput
10 year data integrity
|
|
The AT3515 is an entry-level low cost solid-state flash drive, with a maximum capacity of 8Gbyte in an extremely compact low profile 3.5" form-factor. It is completely solid state, with no moving parts. This contributes to the unit's exceptional ruggedness and wide operating temperature range; with no moving parts, there is no mechanism for mechanical wear-out. Being 100% IDE compatible, no special drivers or flash file managers are required. It is a virtual drop in replacement for standard rotating media.
The AT3515 employs sector erasable NAND E2PROMs (Flash) to deliver up to 8Gbytes of uncompressed, non-volatile solid state storage in an extremely small, rugged form factor. Sequential sustained data throughput is up to 6 Mbytes/sec for reads and 6 Mbytes/sec for writes. The drive supports up to PIO Mode-4 and DMA Mode-2 bus access, multi-sector transfers, as well as LBA addressing. It is 100% IDE compatible and requires no special drivers to operate
The drive is implemented using a custom IDE Flash controller with multi-tasking technology. An integrated 72-bit Reed-Solomon error detection and correction mechanism and proprietary remapping and wear-leveling technology along with a power hold-up circuit greatly improve data reliability. Its' cost effectiveness and low-power operation make the AT3515 ideal for applications requiring high reliability at a low cost up to 8Gbytes of data storage.
The drive is available in a number of standard capacities from 128 to 8 Gbyte. Please contact the factory for specific size availability.
Each drive is fully tested under environmental and voltage extremes to guarantee data integrity under even the harshest conditions.
The drive may be mounted in any orientation. Bottom and side mounting holes are available that conform to the 3.5" IDE drive standard. |
| Back to top |
|
|
