|
|
 |
Memtech 2.5" IDE and SATA Solid State
Flash Drives |
|
|
|
AT2550
Wolverine - 2.5" IDE Solid State Flash Drive |
|
|
| This
product has reached End-of-Life status but limited quantities
are still available. Please contact the SSD Team at (949)
260-8345 for last time purchase and replacement product
information. |
| PDF
Data Sheet | User
Guide |
|
4.8 Gbyte capacity under 9.5mm
8.7 Gbyte capacity under 12.5mm
27 Gbyte maximum capacity
Full -55°C to +125°C military temperature range
2.5" drive low profile form-factor
UDMA-66 compliant IDE interface
16 byte CRC/ECC and Active Remap<(TM)for exceptional data reliability
Kicker(TM) Hold Up Circuit
|
Active Remap(TM) Data Reliability Feature
5 volt, low power operation
Completely solid state - no moving parts
1000G operating shock
15G operating vibration
0.1 millisecond random access time
26 Mbyte/sec cached Read performance
20 Mbyte/sec cached Write performance
5 year product warranty
8 million erase/write cycle endurance
|
|
The AT2550 solid-state flash drive is an UDMA-66 compliant IDE memory module offered in an extremely low profile 2.5 inch drive form-factor. The drive is completely solid state, with no moving parts. This contributes to the unit's exceptional ruggedness and wide operating temperature range; with no moving parts, there is no mechanism for mechanical wear-out. Being 100% IDE compatible, no special drivers or flash file managers are required to interface the drive. It is a virtual drop in replacement for standard rotating media.
The primary storage media in the drive is sector-erasable NAND E2PROMs (Flash). Using these devices, Memtech is able to deliver up to 27 Gbytes of uncompressed, non-volatile solid-state storage in an extremely small, rugged form-factor. The access time for the drive is under 0.1 milliseconds, which permits thousands of transactions to occur per second. Cached read data performance is 26 Mbytes/second, and cached write performance is 20 Mbytes/second.
The Kicker(TM) Hold Up Circuit, using ultra-cap technology, meets all the requirements for a robust and reliable solution. Ultra-caps are new, high-energy capacitors that offer an extremely low ESR, wide operating temperature and small footprint. Unlike batteries, they offer a much more robust form of energy storage, with a wider operating temperature and longer life. Combined with some innovative firmware control, back-EMF and surge current suppression and power monitoring, the Kicker(TM) virtually eliminates the chance of corrupted data in the flash array due to a power loss.
The interface is implemented using a commercially available UDMA-66 compliant IDE controller with a large buffer and a 16-byte combination CRC/ECC error detection and on-the-fly correction mechanism that greatly improves data reliability. The CRC/ECC circuitry, in conjunction with Memtech's proprietary Active Remap(TM) technology, makes for a virtually bulletproof medium for data storage. The drive supports advanced PIO, DMA and UDMA transfer modes, multi-sector transfers, and LBA addressing.
The AT2550 is available now in standard capacities ranging from 1 to 27 Gbytes. The AT2550 low profile solution of 1 to 4.8 Gbytes capacities is available in a 9.5mm height and up to 8.7 Gbytes capacity within a 12.5mm height restriction.
Every drive is subjected to Memtech's EnduroTest(TM) in which it is fully tested under environmental and voltage extremes to guarantee data integrity under even the harshest conditions, and to ensure full functionality out of the box.
The AT2550 may be mounted in any orientation. Eight mounting holes are available: four on the bottom and four on the sides. All holes are tapped 3mm with a maximum penetration of 1.5mm.
|
|
Back to top
|
|
AT2515
Bulldog - 2.5" IDE Solid State Flash Drive |
|
|
| This
product has reached End-of-Life status but limited quantities
are still available. Please contact the SSD Team at (949)
260-8345 for last time purchase and replacement product
information. |
| PDF
Data Sheet | User
Guide |
|
64Mbyte to 8Gbyte uncompressed capacity
Full -40°C to +85°C industrial temp. range
Low profile 3.5" drive form-factor
Standard 44 pin, 2 mm IDE interface
PIO Mode-4 and DMA Mode-2 support
72-bit ECC for exceptional data reliability
|
5 volt, low power operation
Completely solid state - no moving parts
1000G operating shock
15G operating vibration
6 Mbytes/sec sustained Read throughput
6 Mbytes/sec sustained Write throughput
10 year data integrity
|
|
The AT2515 is the low cost in the Rocket Family of drives available today. With a maximum capacity of 8Gbyte in an extremely compact low profile 2.5" form-factor and exceptional speed, the AT2515 is a cost effective solution. It is completely solid state, with no moving parts. This contributes to the unit's exceptional ruggedness and wide operating temperature range; with no moving parts, there is no mechanism for mechanical wear-out. Being 100% IDE compatible, no special drivers or flash file managers are required. It is a virtual drop in replacement for standard rotating media.
The AT2515 employs sector erasable NAND E2PROMs (Flash) to deliver up to 8Gbytes of uncompressed, non-volatile solid state storage in an extremely small, rugged form factor. Sequential sustained data throughput is up to 6 Mbytes/sec for reads and 6 Mbytes/sec for writes. The drive supports up to PIO Mode-4 and DMA Mode-2 bus access, multi-sector transfers, as well as LBA addressing. It is 100% IDE compatible and requires no special drivers to operate
The drive is implemented using a custom IDE Flash controller with multi-tasking technology. An integrated 72-bit Reed-Solomon error detection and correction mechanism and proprietary remapping and wear-leveling technology along with a power hold-up circuit greatly improve data reliability. It's cost effectiveness and low-power operation make the AT2515 ideal for applications requiring high reliability at a low cost up to 8Gbytes of data storage.
The drive is available in a number of standard capacities from 64 to 8 Gbyte. Please contact the factory for specific size availability.
Each drive is fully tested under environmental and voltage extremes to guarantee data integrity under even the harshest conditions.
The drive may be mounted in any orientation. Both bottom and side mounting holes are available that conforms to the 2.5" IDE drive standard.
|
|
Back to top
|
|
 |
|
